|
PTR-200
SPECIFICATIONS
|
|
|
|
|
|
General Dimensions
|
|
|
|
|
|
|
Base Module:
|
H: 5.0" (127mm), W: 10.25"
(260mm), D: 5.0" (127mm).
|
|
Control Panel:
|
H: 5.0" (127mm), W: 8.0"
(203mm), D: 1.0" (25mm).
|
|
External Power Supply:
|
H: 2.4" (60mm), W: 4.1"
(105mm), L: 12.5" (320mm).
|
|
|
|
|
Electrical
Requirements
|
|
|
|
|
|
|
Base Module:
|
12.5 VDC, 13 A. (Provided by external
powers supply)
|
|
Control Panel:
|
12.5 VDC, 500 mA. (Provided from base
module)
|
|
External Power Supply:
|
Voltage: 100-120 / 200-240
VAC.
|
|
|
Current: 4.5 / 2.2 A.
|
|
|
Frequency: 47-63 Hz.
|
|
|
|
|
|
Supply Requirements
|
|
|
|
|
|
|
All Modules Except RPT:
|
Vacuum for fiber holding blocks.
(External vacuum pump available)
|
|
Automatic Recoat Modules:
|
80-120 psi dry compressed air or gas
for pneumatic gripper.
|
|
|
|
|
Interface
|
|
|
|
|
|
|
Base Module:
|
RS-232 Serial Communication.
|
|
|
|
|
|
|
|
|
Recoating
|
Manual
|
Automatic
|
|
|
|
|
Modules:
|
MRC, XLR.
|
ARC, ARL.
|
|
|
|
|
Recoat Mold:
|
Quartz.
|
Quartz.
|
|
|
|
|
Recoat Diameter:
|
260mm std. for nominal 250mm fiber.
|
280mm std. for nominal 250mm fiber.
|
|
Custom sizes from 200mm and up.
|
Custom sizes are available.
|
|
|
|
|
Maximum Recoat Length:
|
2" (50 mm) for MRC
Module.
|
2" (50 mm) for both
Modules.
|
|
4" (100 mm) for XLR
Module.
|
|
|
|
|
|
Recoat Material:
|
UV Curable Arcylate.
|
UV Curable Acrylate.
|
|
DSM 950-200 recommended.
|
DSM 950-200 recommended.
|
|
|
|
|
UV Source:
|
Four 10 W halogen lamps, for
MRC.
|
Twelve 10 W halogen lamps,
ARC/ARL.
|
|
Eight 10 W halogen lamps, for
XLR.
|
|
|
|
|
|
Recoat Injection:
|
Automatic, direct from 1 oz.
bottle.
|
Automatic, direct from 1 oz.
bottle.
|
|
|
|
|
Recoat Volume:
|
Programmable in microliters,
5ml
typ..
|
Programmable in microliters,
1.5ml
typ..
|
|
|
|
|
Recoat Inject Rate:
|
Programmable, up to 1.8ml/s.
|
Programmable, up to 1.8ml/s.
|
|
|
|
|
Inject/Lamp-on Delay Time:
|
Programmable, 5s typ..
|
Programmable, 5s typ..
|
|
|
|
|
Cure Time:
|
Programmable, 17s typical.
|
Programmable, 17s typical.
|
|
|
|
|
Mold Cleaning Requirement:
|
After every recoat.
|
Start-up and shut-down only.
|
|
|
|
|
Mold Open/Close Method:
|
Manual.
|
Automatic. (pneumatic
gripper)
|
|
|
|
|
Total Cycle Time:
|
60s typ..
|
45s typ..
|
|
|
|
|
|
|
|
Proof Testing
|
Rotary
|
Linear
|
|
|
|
|
Modules:
|
RPT.
|
LPT, ARL.
|
|
|
|
|
Load Application:
|
Rotating Mandrel.
|
Linear Fiber Clamp.
|
|
|
|
|
Mandrel Diameter:
|
2" (51mm).
|
N/A.
|
|
|
|
|
Fiber Clamp Length:
|
N/A.
|
1.5" (38mm).
|
|
|
|
|
Fiber Spacing:
|
5" (127mm).
|
2.9" (74mm).
|
|
|
|
|
Min. Fiber Length Req.:
|
17" (432mm).
|
6" (150mm).
|
|
|
|
|
Maximum Load:
|
20 lbs., 9.1 kg..
|
4.5 lbs., 2.1 kg..
|
|
>800 kpsi (5.5 Gpa) for
125mm
fiber.
|
235 kpsi (1.6 Gpa) for 125mm fiber.
|
|
|
|
|
Accuracy:
|
+/- 2%.
|
+/- 2%.
|
|
|
|
|
Ramp Rate:
|
Manual adjust up to 5 lbs/s (2.3
kg/s).
|
Programmable, up to 5 lbs/s (2.3
kg/s).
|
|
|
|
|
Hold Time:
|
N/A.
|
Programmable.
|
|
|
|
|
Display Units:
|
lbs, kg, N, kpsi, GPa.
|
lbs, kg, N, kpsi, GPa.
|
